Affiliate disclosure: Some links on this page are affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.
BEHR Premium Wet-Look Sealer (No. 985) is a water-based, high-gloss clear acrylic for concrete, pavers, brick, stone and stucco, sold at Home Depot. It is for homeowners who want a shiny, color-deepening finish on a patio, walkway or paver area with low odor and water cleanup. The bottom line: it does deliver the wet look and goes on easily, but like other thin acrylic films it wears in traffic, can get slick when wet, and needs maintenance coats.
| Type | Film-forming topical sealer |
| Chemistry | Water-based acrylic; about 25% solids by volume; under 100 g/L VOC |
| Finish | High gloss (80–90 at 60°), non-yellowing |
| Coverage | 200–450 sq ft/gal depending on porosity |
| Coats | 2 recommended; BEHR allows up to 4 more for extra gloss |
| Dry/recoat | Dry 1 hour; recoat 4 hours |
| Cure | Heavy foot traffic, furniture and tires after 24–72 hours; no washing for 30 days |
| Best for | Patios, walkways, pavers, brick, unglazed tile, stucco |
| Not for | Wood, metal, granite, marble, terrazzo, areas right next to pools, hydrostatic pressure, over oil-based products |
| New concrete | Wait 30 days, then etch |
Watch: BEHR Wet-Look No. 985 in 60 seconds
What It Is / How It Works
BEHR currently markets this product as BEHR PREMIUM Concrete, Brick & Tile Wet-Look Sealer, and Home Depot lists it as BEHR PREMIUM Wet-Look Sealer (model 98501 for the gallon, 98505 for 5 gallons). It is the same No. 985 product.
It is a clear acrylic resin in water. It looks milky in the can, goes on white and dries clear, leaving a thin glossy film on the surface. That film darkens and enriches the color of the masonry (the "wet look") and repels water and stains. BEHR says water and stain repellency begin within 24 hours. The data sheet lists about 25% volume solids, which is typical for a water-based acrylic, and a high-gloss reading of 80–90 at 60°. BEHR describes the resin as non-yellowing.
Because it is a surface film rather than a penetrating treatment, it will eventually wear in high-traffic areas. BEHR says as much, noting that horizontal surfaces may see excessive wear and need periodic touch-ups or maintenance coats.
Where It Works Best (and where it doesn't)
It is approved for interior and exterior, vertical and horizontal surfaces, coated or uncoated: concrete, exposed aggregate, pavers, brick, Mexican and other unglazed tile, unpolished natural and manufactured stone, masonry and stucco. It looks best on colored or textured surfaces where the gloss brings out the pattern, such as paver patios, brick walkways and stamped concrete.
BEHR does not recommend it for wood, metal, granite, marble, terrazzo, areas immediately next to pools, surfaces with hydrostatic pressure, or over oil-based products. It also warns that sealed surfaces can become slippery when wet, which matters on steps, ramps and pool surrounds. Although BEHR lists a 24–72 hour wait for car tires, it is not a dedicated garage-floor coating. For garages, see our best epoxy floor coatings.
Owner feedback is mixed. The Home Depot gallon listing averaged about 3.8 out of 5 across more than 3,500 reviews when we checked, which reflects a product that looks great when applied right but is sensitive to prep, coat thickness and wear.
Pros
- Strong high-gloss wet look that deepens color
- Water-based, low odor, water cleanup
- Fast: dry in 1 hour, recoat in 4 hours
- Works on many masonry types, inside and out, including vertical surfaces
- Non-yellowing acrylic
- Easy to find at Home Depot in gallon and 5-gallon sizes
Cons
- Thin surface film that wears and needs maintenance coats
- Slippery when wet; consider an anti-slip additive on walkways
- Not for use right next to pools, on marble or granite, or over oil-based products
- Narrow application window (50–80°F, no direct sun)
- Bare concrete needs etching, and some surfaces need BEHR's No. 880 primer
- Mixed owner ratings overall
How to Apply It
- New concrete: let it cure 30 days, then clean and etch to a texture like 150-grit sandpaper. Rinse off all residue and let it dry completely. The data sheet calls for a surface pH of 10 or lower.
- Existing surfaces: clean off dirt, oil, grease and mildew. Strip or scrape failing coatings and scuff-sand glossy areas. On stamped concrete, use a cleaner that removes release agent. Spot-etch any bare concrete.
- Prime where needed. BEHR recommends its No. 880 Bonding Primer on porous or rough horizontal concrete, brick or stone exposed to tires, foot traffic or moisture, and on areas treated for efflorescence or laitance.
- Check the weather. Air and surface between 50°F and 80°F, no direct sun, a dry surface, and no rain or heavy dew for 24 hours.
- Apply a thin coat with a pump sprayer (then back-roll), pad, nylon/polyester brush or roller. Do not thin, and do not let it puddle.
- Recoat after 4 hours. Two coats is the standard. BEHR allows additional thin coats for more gloss.
- Cure. Wait 24–72 hours for heavy foot traffic, furniture and tires, and 30 days before washing the surface.
How It Compares
BEHR Premium Low-Lustre Sealer (No. 986). The same family, with a softer sheen. Choose it if you want enhanced color without the high gloss and with somewhat less glare.
H&C ClariShield Water-Based Wet Look. Sherwin-Williams' water-based acrylic gloss sealer. It is similar in concept and also designed as a topcoat over H&C's water-based concrete stains. Both are thin films that reward thin coats.
Penetrating water repellents. If you want long-lasting water and salt protection on a driveway without any shine or peeling, a silane/siloxane sealer is the better tool. See our best silane-siloxane concrete sealers guide.
FAQ
Is BEHR Wet-Look Sealer water-based or solvent-based?
Water-based. It is milky in the can, dries clear, has under 100 g/L VOC, and tools clean up with water.
How long does BEHR Wet-Look Sealer last?
BEHR does not give a lifespan. It notes that horizontal surfaces may wear and need touch-ups or maintenance coats. Expect to refresh high-traffic, sun-exposed areas more often than walls or covered patios.
Can you put BEHR Wet-Look over an old sealer?
It is approved for previously coated surfaces, but not over oil-based products. Remove failing sealer, scuff-sand glossy areas, clean well and test a small spot first.
Can I use it on a pool deck?
BEHR does not recommend it for areas immediately adjacent to pools, and the gloss can be slippery when wet. A sealer made for pool decks, with an anti-slip additive, is a safer choice.
Verdict
BEHR Premium Wet-Look Sealer No. 985 is a convenient, low-odor way to give pavers, brick and decorative concrete a glossy, deeper color. It is easy to find and quick to recoat. It is also a thin film with a narrow temperature window, slip concerns and regular maintenance, so it suits patios and walkways better than driveways, pool decks or garages. Our rating: 3.6/5.
See the manufacturer's product page
How we reviewed this product: this is a research-based review built from the manufacturer's technical data sheet and current retail listings. We have not run our own hands-on tests of this product. Details were checked in October 2026; always follow the current label.




