Concrete Sealer Reviews

  • Home
  • Best Concrete Sealers
  • Product Reviews
  • About Us
KILZ 1-Part Epoxy review – rated 3.5/5
0
Thursday, 29 October 2026 / Published in PRODUCT REVIEWS

KILZ 1-Part Epoxy Concrete & Garage Floor Paint Review

Affiliate disclosure: Some links on this page are affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.

KILZ 1-Part Epoxy is a water-based, single-component floor paint for garages, basements, porches and other horizontal concrete, sold in gallon cans. It is aimed at DIYers who want a colored, cleanable floor without mixing a 2-part kit. The bottom line: it is a capable residential floor paint with solid published specs, but it builds a thin film, needs a separate bonding primer on bare concrete, and is not a substitute for a true epoxy in a hard-working garage.

TypeSingle-component floor paint
ChemistryWater-based acrylic/epoxy; about 31–33% solids by volume
FinishLow sheen (10–20 at 60°); Silver Gray, Slate Gray, white and deep tint bases
Coverage300–500 sq ft/gal (rough 300–400, smooth 400–500)
Coats1–2 (no more than 2), over bonding primer on bare concrete
Dry/recoatDry to touch about 1 hour at 77°F (KILZ’s product page says 2 hours); recoat 4–6 hours
CureHeavy foot traffic 72 hours; vehicles 7 days; no washing for 30 days
Best forResidential garages with light use, basements, porches
Not forVertical surfaces, hydrostatic pressure, industrial use, forklifts
New concreteWait at least 30 days
At a glance (product details checked October 2026)

Watch: KILZ 1-Part Epoxy in 60 seconds

What It Is / How It Works

KILZ now markets this product as KILZ 1-Part Epoxy Acrylic Concrete & Garage Floor Paint. The added word "Acrylic" is an honest description of what it is: a water-based acrylic floor paint modified with epoxy for hardness and adhesion. There is no hardener to mix and no pot life. You stir and roll.

KILZ publishes more technical detail than most products in this class. The data sheet lists about 33% volume solids (the product page says 31%), under 50 g/L VOC, and a dry film of roughly 1.0 to 1.6 mils per coat depending on spread rate. That film thickness is the key to understanding its limits. A typical 2-part epoxy builds a much thicker film, which is why it resists hot tires, chemicals and abrasion better. KILZ says this paint resists hot-tire pickup, but it gives no rating, and it limits the product to residential use.

Unlike BEHR's current self-priming 1-part epoxy, KILZ calls for a separate primer. On new or uncoated concrete it wants a clean, etched surface followed by KILZ Concrete & Masonry Bonding Primer. That is an extra step and an extra product, but a primer coat is also good insurance for adhesion on a garage floor.

Where It Works Best (and where it doesn't)

Good fits are interior or exterior porous concrete, masonry, stone and brick floors: basements, porches, pool decks, laundry rooms and garages where a car is parked occasionally or tire lanes get a yearly touch-up. KILZ itself recommends planning on an annual touch-up in tire-traffic areas.

Skip it on walls (it is for horizontal surfaces only), slabs with water pushing up from below, shops with forklifts or heavy equipment, and any commercial or industrial floor. If the garage floor gets daily hot tires, dropped tools and road salt, a 2-part epoxy or polyaspartic system will last much longer. See our best epoxy floor coatings guide. The data sheet sets no moisture limit, so do a simple moisture check on basement slabs before you buy (tape a square of plastic down overnight and look for darkening).

Pros

  • No mixing, no pot life, soap-and-water cleanup
  • Low VOC (under 50 g/L)
  • Clear, detailed technical data sheet (solids, film build, sheen)
  • Good coverage at 300–500 sq ft per gallon
  • Interior and exterior use; two-year shelf life unopened
  • Full system available (etcher, degreaser, stripper, bonding primer)

Cons

  • Thin film (about 1–1.6 dry mils per coat) compared with 2-part epoxy
  • Needs a separate bonding primer on new or bare concrete
  • 7 days before vehicles and 30 days before washing
  • Residential use only; not for forklifts or industrial floors
  • Annual touch-ups expected in tire lanes
  • Sold in gallons only, and wet surfaces can be slippery

How to Apply It

  1. Let new concrete cure at least 30 days. Do not use it on slabs with hydrostatic pressure.
  2. Prep bare concrete. Clean and etch (KILZ Concrete & Masonry Cleaner & Etcher), rinse well and let the floor dry completely.
  3. Prep painted or sealed floors. Either strip the whole floor, or remove loose paint, scuff-sand, degrease and etch any bare spots. Old paint may contain lead, so use proper dust control.
  4. Prime. Apply KILZ Concrete & Masonry Bonding Primer on new or bare concrete, or spot-prime bare areas on coated floors.
  5. Check conditions. Air and surface temperatures between 50°F and 90°F. Avoid direct sun, and do not apply if the floor is hot to the touch.
  6. Apply a thin, even coat with a 3/8" to 1/2" nap roller, a nylon/polyester brush or an airless sprayer. Mix all cans together first and do not thin.
  7. Second coat if needed after 4–6 hours, applied crosswise. No more than two coats.
  8. Cure. Heavy foot traffic and furniture after 72 hours, vehicles after 7 days (cardboard under tires is allowed after 72 hours), and no rinsing or cleaning for 30 days.

How It Compares

BEHR Premium Self-Priming 1-Part Epoxy. Nearly identical on paper: 300–500 sq ft per gallon, 50–90°F application, a 7-day wait for tires and the same list of restrictions. BEHR's current version is self-priming, which saves a step. KILZ's primer-first approach is more work but adds a dedicated bonding layer.

2-part epoxy kits. Thicker, harder and more chemical-resistant, with a short working time after mixing. They are the better match for a garage that sees daily vehicle use.

Clear penetrating sealer. If you like the bare concrete look and mainly want to keep water, salt and oil out, a penetrating sealer will not peel or show tire marks. See our best concrete sealers for 2026.

FAQ

Do I need a primer with KILZ 1-Part Epoxy?

On new or uncoated concrete, yes. KILZ's directions call for cleaning and etching, then KILZ Concrete & Masonry Bonding Primer. On sound, previously painted floors, spot-prime any bare concrete.

Does KILZ 1-Part Epoxy resist hot tire pickup?

KILZ says it resists hot-tire pickup but gives no rating. It also advises a 7-day cure before driving on it and annual touch-ups in tire areas, which tells you its limits compared with a 2-part epoxy.

Can I use it on basement walls?

No. It is for horizontal surfaces only and not for areas with hydrostatic pressure, which rules out many damp basement walls.

How long does it last?

KILZ does not give a lifespan. It backs the product with a one-year limited warranty and expects tire lanes to need a touch-up each year. Low-traffic floors such as porches and basements will go longer between recoats.

Verdict

KILZ 1-Part Epoxy Acrylic is a fair, well-documented residential floor paint. It is easy to apply, low in odor and covers well. Its value depends on doing the full system (etch, prime, two thin coats, a week before tires) and accepting that it is a paint, not a heavy-duty garage coating. Our rating: 3.5/5.

See the manufacturer's product page and data sheet

How we reviewed this product: this is a research-based review built from the manufacturer's technical data sheet and current retail listings. We have not run our own hands-on tests of this product. Details were checked in October 2026; always follow the current label.

Where to Buy

Check Price on Amazon

  • KILZ 1-Part Epoxy Concrete & Garage Floor Paint, Silver Gray (1 gal.)
  • KILZ 1-Part Epoxy Concrete & Garage Floor Paint, Slate Gray (1 gal.)

Related Guides

  • Best Epoxy Floor Coatings for Garages & Basements
  • RockSolid Polycuramine Garage Floor Coating Kit Review
  • How to Test Concrete for Moisture
  • How to Acid Etch Concrete
  • Best Concrete Sealers for 2026

What you can read next

Rainguard Micro-Seal review – rated 4.2/5
Rainguard Micro-Seal Penetrating Water Repellent Review
Kryton Krystol T1 review – rated 4.3/5
Kryton Krystol T-1 Review
QUIKRETE Cure & Seal review – rated 3.6/5
Quikrete Acrylic Concrete Sealer Review

Search

Interesting Posts

  • Spalled concrete with flaking surface and exposed aggregate next to a smooth, broom-finished resurfaced section

    Spalling Concrete: What Causes It and How to Fix It

    Spalling concrete flakes and pits when water fr...
  • OKON S-40 review – rated 4.1/5

    Rust-Oleum OKON S-40 Water Repellent Sealer Review

    Affiliate disclosure: Some links on this page a...
  • Rainguard Micro-Seal review – rated 4.2/5

    Rainguard Micro-Seal Penetrating Water Repellent Review

    Affiliate disclosure: Some links on this page a...
  • Valspar Waterproofer review – rated 3.7/5

    Valspar Concrete & Masonry Waterproofer Review

    Affiliate disclosure: Some links on this page a...
  • BEHR Wet-Look No. 985 review – rated 3.6/5

    BEHR Premium Wet-Look Sealer (No. 985) Review

    Affiliate disclosure: Some links on this page a...

ABOUT US

ABOUT US

Concrete Sealer Reviews helps homeowners and contractors choose the right sealer, waterproofer or coating for driveways, garages, basements and patios. Articles are written by Mark Dominic. We earn affiliate commissions on some purchases, and some brands featured here have a business relationship with this site.

Subscribe to our newsletter to receive the latest news and articles!

Be the latest to read new product reviews!

  • Home
  • Best Concrete Sealers
  • Product Reviews
  • About Us

© 2026. All rights reserved. Concrete Sealer Reviews

TOP