Affiliate disclosure: Some links on this page are affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.
Valspar Concrete & Masonry Waterproofer is a clear, water-based siloxane sealer sold at Lowe’s for bare driveways, patios, walkways, pool decks and basement slabs. It soaks in rather than forming a film, so it is aimed at homeowners who want water to bead up without changing how the concrete looks. The bottom line: it is an easy, low-odor, budget-friendly water repellent for porous concrete, but Valspar publishes very little technical data for it, and it is not a fix for wet basements or a protective topcoat.
| Type | Penetrating water repellent (non-film-forming) |
| Chemistry | Water-based siloxane |
| Finish | Clear, matte; does not change color or texture |
| Coverage | Not published on Valspar’s product page; check the can label |
| Coats | 1–2, second coat applied wet-on-wet |
| Dry/recoat | Touch dry 1–2 hours; recoat in 5–10 minutes (77°F, 50% RH) |
| Cure | Not stated by the manufacturer |
| Best for | Bare, porous driveways, patios, walkways, pool decks, basement floors |
| Not for | Painted or previously sealed surfaces; dense surfaces that won’t absorb water |
| New concrete | Wait at least 30 days; new pavers 60 days |
Watch: Valspar Waterproofer in 60 seconds
What It Is / How It Works
This is a penetrating sealer. Valspar describes it as a "siloxane formula that penetrates the surface to help keep water out." Siloxanes react inside the pores of concrete and masonry and leave behind a water-repellent lining. Water beads on the surface instead of soaking in, but the concrete can still breathe, so moisture inside the slab can escape as vapor.
Because nothing builds up on top, the surface keeps its natural look and texture. There is no gloss, no "wet look" and no film to peel. Valspar says it helps guard against water, salt, dirt, chemicals and freeze/thaw cycles, which is the standard job description for this type of product.
At Lowe's the same product is listed as "Valspar Clear Matte Transparent Water-based Interior/Exterior Waterproofer" (model 024.0082490.007). Older Valspar concrete products, such as the silicone-based Natural Look Waterproofer and the acrylic Wet Look sealer, are different formulas, so don't mix up their specs with this one.
Where It Works Best (and where it doesn't)
It works best on bare, absorbent concrete and masonry: broom-finished driveways, sidewalks, patios, pool decks and pavers, plus interior slabs such as basement floors. Valspar says the surface should feel at least as rough as 120-grit sandpaper and should readily absorb water. If water sits on the surface instead of darkening it, the sealer won't be able to penetrate.
It is not for painted or previously sealed concrete. When a Lowe's shopper asked about using it over concrete paint, the Valspar team answered that it should not be applied over sealed surfaces because "the product must be able to soak into the concrete." It also won't stop water pushing through a basement wall or floor under pressure, won't fill cracks, and won't give you stain protection like a film-forming sealer. For a full rundown of options, see our guide to the best silane-siloxane concrete sealers.
Pros
- Invisible, matte finish that doesn't change color or texture
- Water-based, soap-and-water cleanup
- Breathable; no film to peel, blush or wear off in traffic lanes
- Fast wet-on-wet second coat (5–10 minutes)
- Easy to find at Lowe's, with strong average ratings from buyers
Cons
- Very limited published data: no coverage rate, actives percentage or expected service life on the product page
- Bare surfaces only; can't go over paint or old sealer
- Doesn't stop hydrostatic pressure or leaks through cracks
- Little oil or stain resistance compared with film-forming sealers
- Sold mainly in 1-gallon cans, which adds up on large driveways
How to Apply It
- Check the timing. New concrete must cure at least 30 days. New pavers should weather at least 60 days, with excess joint sand swept off.
- Clean thoroughly. Remove grease, oil, paint and old sealers. Valspar recommends a high-pressure water wash. Let the surface dry completely.
- Do a water test. Sprinkle water on the surface. It should soak in and darken the concrete. If it beads, the surface is sealed or too dense.
- Apply with a roller or low-pressure garden sprayer. Work in manageable sections and don't let it pond or puddle.
- Add a second coat wet-on-wet if needed. Valspar says to apply the second coat while the first is still wet, about 5–10 minutes later, for maximum protection.
- Wipe off excess. After 5–10 minutes of penetration time, wipe any unabsorbed product with a clean, dry cloth so it doesn't leave residue.
- Let it dry. It is dry to the touch in 1–2 hours at 77°F and 50% humidity. Cooler or more humid weather slows drying. Valspar doesn't publish a full cure time or traffic schedule, so give it extra time before driving on it.
How It Compares
Rust-Oleum OKON S-40 is also a water-based silane/siloxane, but it comes with a full technical data sheet: published coverage rates, about 3/8" of penetration, test data, and an optional 5-year water repellency warranty for registered projects. If you want to know exactly what you're buying, S-40 is the better-documented choice.
Rainguard Micro-Seal is another zero-VOC silane/siloxane sold at Home Depot. Its data sheet includes coverage charts and freeze/thaw and wind-driven rain test results. It is a good alternative if you also want to treat brick, stucco or wood with the same product.
If you want color enhancement or a sheen, a film-forming acrylic is a different category entirely. Our Best Concrete Sealers for 2026 guide covers both types.
FAQ
Is Valspar Concrete & Masonry Waterproofer really waterproof?
It is a water repellent, not a waterproof membrane. It makes surface water bead up and reduces absorption, but it will not stop water forced through a slab or wall by hydrostatic pressure, and it won't seal cracks.
Can I put it over painted or sealed concrete?
No. Valspar says the surface must be free of paint and sealers, and its customer team has stated it should not be used over sealed surfaces because it has to soak in to work.
Will it make my concrete look wet or shiny?
No. It dries clear and matte and is designed not to change the color or texture of the surface. If you want a darker, glossy look, you need a film-forming acrylic sealer instead.
How long does it last?
Valspar doesn't publish a service life. A simple way to know when to reapply is to sprinkle water on the surface once or twice a year. When it stops beading and starts soaking in, it's time for another coat.
Verdict
Valspar Concrete & Masonry Waterproofer is a convenient, invisible water repellent for bare, porous concrete, and Lowe's shoppers rate it well. The weak spot is documentation: with no published coverage, actives content or service life, it's hard to compare against better-documented silane/siloxane products. It's a reasonable pick for a patio or walkway you want to keep looking natural, as long as you don't expect it to fix a wet basement. Learn more on Valspar's product page. Our rating: 3.7/5
How we reviewed this product: this is a research-based review built from the manufacturer's technical data sheet and current retail listings. We have not run our own hands-on tests of this product. Details were checked in October 2026; always follow the current label.




